MAGICXPRESS MX56V - X Card Type Modem/Fax card Chip Set Unidentified I/O Options Line out, phone in, microphone in, speaker out Maximum Modem Rate 56Kbps (receive only), 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V34, V.32bis, V.32, V.22bis, V.23, V.22, V.21 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29, T.4, T.30 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 8-bit ISA Card Size Half-length [Image] CONNECTIONS Function Label Function Label Line out CN1 Speaker out CN3 Phone in CN2 Microphone in CN4 SERIAL PORT ADDRESS Setting JP1/A JP1/B JP1/C COM1 (3F8h) Closed Closed Closed COM2 (2F8h) Open Closed Closed COM3 (3E8h) Closed Open Closed COM4 (2E8h) Open Open Closed Plug and play enabled Open Open Open INTERRUPT Setting JP2/A JP2/B JP2/C JP2/D JP2/E IRQ2 Open Open Open Open Closed IRQ3 Open Open Open CloOpen IRQ4 Open Open CloOpen Open IRQ5 Open Closed Open Open Open IRQ7 Closed Open Open Open Open Note: Interrupt must be set to IRQ3 to enable plug and play. SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, F, H, M, O, P, T, V &C, &G, &T, &W, &Z S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S38 Note: See MHI Help File for full command documentation. Proprietary AT Command Set COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.25 at 300 or 1200bps B1 Bell 300 or 212A at 300 or 1200bps DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D/ Delays for 125 msec. before proceeding with dial D#,D* Extended touch tone pad tones D$ Displays a list of dial commands REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports four digit product code I1 Reports ROM checksum I2 Reports results of RAM self test I3 Reports product type I4 Reports current modem settings I5 Reports NVRAM settings I6 Reports link diagnostics I7 Reports product configuration I9 Reports plug and play information I11 Reports call statistics SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Displays result codes when in answer mode SELECT CALL PROGRESS RESULT CODES Type: Configuration Format: AT [cmds] Xn [cmds] Description: Enables selection of tone detection and associated result code format options Command Function X0 Busy and dial tone detection disabled; result codes 0 - 4 enabled. X1 Busy and dial tone detection disabled; result codes 0 - 5, 10, & 13 - 220 enabled. X2 Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6, 10, & 13 - 220 enabled. X3 Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5,7 - 8, 10, & 13 - 220 enabled. X4 Busy and dial tone detection enabled; result codes 0 -8, & 10 - 220 enabled. X5 Busy tone detection enabled, dial tone detection disabled, result codes 0 - 5, 7 - 8, & 10 - 220 enabled X6 Busy and dial tone detection enabled, result codes 0 -8, & 11 - 220 enabled RESET DEFUALT CONFIGURATION Type: Configuration Format: AT [cmds] Yn [cmds] Description: Tells the modem which profile to use the next time the modem is turned on or reset Command Function Y0 NVRAM configuration 0 Y1 NVRAM configuration 1 Y2 Factory configuration 0 Y3 Factory configuration 1 Y4 Factory configuration 2 SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM using the &W command. Command Function Z0 Restore NVRAM setting selected by Y command Z1 Restore NVRAM setting 0 Z2 Restore NVRAM setting 1 Z3 Restore factory default setting 0 (&F0) Z4 Restore factory default setting 1 (&F1) Z5 Restore factory default setting 2 (&F2) COMMANDS Type: Configuration Format: AT [cmds] &$ [cmds] Description: Displays a list of ampersand commands MODIFY RESPONSES Type: Configuration Format: AT [cmds] &An [cmds] Description: Determines whether the modem sends MNP responses Command Function &A0 ARQ result codes disabled &A1 ARQ result codes enabled &A2 Append additional V.32 indicator in result codes &A3 Append additional LAPM/MNP/NONE and V.42bis/MNP5 in result codes SERIAL PORT RATE Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Controls DTE interface speed Command Function &B0 Change serial port speed to match rate of connection &B1 Serial port speed is independent of connection speed &B2 In answer mode, serial port speed is fixed only for ARQ calls DATA TERMINAL READY Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Controls DTR operations Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 Normal DTR operations FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Sets values to standard factory configuration &F1 Sets values to factory configuration 0 &F2 Sets values to factory configuration 1 FLOW CONTROL Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Enables flow control options Command Function &H0 Flow control disabled &H1 Hardware flow control, clear to send enabled &H2 Software flow control, XON/XOFF enabled &H3 Hardware and software flow control enabled FLOW CONTROL PASS THROUGH Type: Configuration Format: AT [cmds] &In [cmds] Description: Enables flow control options Command Function &I0 XON/XOFF flow control disabled &I1 Process XON/XOFF signals to your modem and remote system &I2 Process XON/XOFF signals to your modem only &I3 Hewlett Packard host mode enabled. Modem receives an ENQ and returns an ACK if the transmit buffers are 90% full or below 30% full. Modem will respond immediately if buffers are empty. &I4 Hewlett Packard terminal mode enabled. Modem receives an ENQ from remote DCE and passes it to the DTE. Modem waits for an ACK before sending further data. &I5 Special flow control enabled DATA COMPRESSION Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables data compression Command Function &K0 Data compression disabled &K1 Auto enable/disable &K2 Data compression enabled &K3 MNP5 disabled, V.42bis enabled COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Normal mode &M4 Normal/ARQ mode &M5 ARQ mode CONNECTION SPEED UPPER LIMIT Type: Configuration Format: AT [cmds] &Nn [cmds] Description: Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed. Command Function &N0 No maximum connect speed. &N1 Set maximum connect speed to 300bps. &N2 Set maximum connect speed to 1200bps. &N3 Set maximum connect speed to 2400bps. &N4 Set maximum connect speed to 4800bps. &N5 Set maximum connect speed to 7200bps. &N6 Set maximum connect speed to 9600bps. &N7 Set maximum connect speed to 12Kbps. &N8 Set maximum connect speed to 14.4Kbps. &N9 Set maximum connect speed to 16.8Kbps. &N10 Set maximum connect speed to 19.2Kbps. &N11 Set maximum connect speed to 21.6Kbps. &N12 Set maximum connect speed to 24Kbps. &N13 Set maximum connect speed to 26.4Kbps. &N14 Set maximum connect speed to 28.8Kbps. &N15 Set maximum connect speed to 31.2Kbps. &N16 Set maximum connect speed to 33.6Kbps. &N17 Set maximum connect speed to 32Kbps &N18 Set maximum connect speed to 36Kbps &N19 Set maximum connect speed to 40Kbps &N20 Set maximum connect speed to 44Kbps &N21 Set maximum connect speed to 48Kbps &N22 Set maximum connect speed to 49.3Kbps &N23 Set maximum connect speed to 50.6Kbps &N24 Set maximum connect speed to 52Kbps &N25 Set maximum connect speed to 53.3Kpbs &N26 Set maximum connect speed to 54.6Kbps &N27 Set maximum connect speed to 56Kbps PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) RECEIVE DATA Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS options Command Function &R1 RTS is ignored by modem. &R2 Modem sends data to DTE only if RTS is on DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected CONNECTION SPEED LOWER LIMIT Type: Configuration Format: AT [cmds] &Un [cmds] Description: Sets slowest allowed connection speed if &N is set to 1 or higher. Command Function &U0 No minimum connect speed. &U1 Set minimum connect speed to 300bps. &U2 Set minimum connect speed to 1200bps. &U3 Set minimum connect speed to 2400bps. &U4 Set minimum connect speed to 4800bps. &U5 Set minimum connect speed to 7200bps. &U6 Set minimum connect speed to 9600bps. &U7 Set minimum connect speed to 12Kbps. &U8 Set minimum connect speed to 14.4Kbps. &U9 Set minimum connect speed to 16.8Kbps. &U10 Set minimum connect speed to 19.2Kbps. &U11 Set minimum connect speed to 21.6Kbps. &U12 Set minimum connect speed to 24Kbps. &U13 Set minimum connect speed to 26.4Kbps. &U14 Set minimum connect speed to 28.8Kbps. &U15 Set minimum connect speed to 31.2Kbps. &U16 Set minimum connect speed to 33.6Kbps. &U17 Set maximum connect speed to 32Kbps &U18 Set maximum connect speed to 36Kbps &U19 Set maximum connect speed to 40Kbps &U20 Set maximum connect speed to 44Kbps &U21 Set maximum connect speed to 48Kbps &U22 Set maximum connect speed to 49.3Kbps &U23 Set maximum connect speed to 50.6Kbps &U24 Set maximum connect speed to 52Kbps &U25 Set maximum connect speed to 53.3Kpbs &U26 Set maximum connect speed to 54.6Kbps &U27 Set maximum connect speed to 56Kbps BREAK HANDLING Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Sets break handling Command Function &Y0 Destructive, but doesn’t sent break &Y1 Destructive, expedited &Y2 Nondestructive, expedited S(STATUS) -REGISTERS BIT-MAPPED REGISTER S13 Format: AT [cmds] S13=n [cmds] Range: 0-174 Unit: Bit-mapped Description: Controls reset, delete, and auto dial.. Bit Value Function 0 0 Does not reset the modem when DTR is not asserted 1 Resets the modem when DTR is not asserted 1 0 Does not reset the non-MNP transmit buffer from 1.5KB to 128B 1 Resets the non-MNP transmit buffer from 1.5KB to 128B 2 0 Backspace key not set to delete 1 Backspace key set to delete 3 0 Does not autodial number stored in NVRAM location 0 when the DTR is asserted 1 Autodials number stored in NVRAM location 0 when the DTR is asserted 4 0 Does not autodial number stored in NVRAM location 0 when software is reset or modem is 1 powered up Autodials number stored in NVRAM location 0 when software is reset or modem is powered up 5 0 Does not disables V.32bis ASL mode 1 Disables V.32bis ASL mode 6 0 1 Does not disable quick retrains Disables quick retrain 7 0 Does not disconnect on escape mode 1 Disconnects on escape mode BIT-MAPPED REGISTER S15 Format: AT [cmds] S15=n [cmds] Unit: Bit-mapped Description: Disable/Enable MNP Bit Value Function 0 0 Enable ARQ/MNP for V.22 1 Disable ARQ/MNP for V.22 1 0 Enable ARQ/MNP for V.22bis 1 Disable ARQ/MNP for V.22bis 2 0 Enable ARQ/MNP for V.32/V.32bis/V.32terbo 1 Enable ARQ/MNP for V.32/V.32bis/V.32terbo 3 0 Enable MNP handshake 1 Disable MNP handshake 4 0 Enable MNP level 4 1 Disable MNP level 4 5 0 Enable MNP level 3 1 Disable MNP level 3 6 0 MNP compatibility 1 MNP incompatibility 7 0 1 Enable V.42 operation Disable V.42 operation TEST MODES Type: Register Format: AT [cmds] S16=n [cmds] Unit: Bit-mapped Description: Controls touch tone dialing test. Bit Value Function 0 0 Reserved 1 0 Touch tone dialing test not in progress 1 Touch tone dialing test in progress 2 0 Test pattern is not being generated 1 Test pattern is being generated 3-7 0 Reserved INACTIVITY TIMER Type: Register Format AT [cmds] S19=n [cmds] Default: 0 Unit: 1 second Description: Activates when there is no activity on the phone line. Modem hangs up at time-out Note: S19=0 disables the timer and allows an indefinite duration. MNP OR V.42 MODE DELAY Type: Register Format AT [cmds] S21=n [cmds] Range: Unidentified Unit: 10ms Description: Sets the length of breaks sent from modem to computer. FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S22=n [cmds] Range: Unidentified Unit: ASCII Description: Sets the character used to represent XON FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S23=n [cmds] Range: Unidentified Unit: ASCII Description: Sets the character used to represent XOFF BIT-MAPPED REGISTER S27 Format AT [cmds] S27=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Enables/disables modulation protocols Bit Value Function 0 0 Disable V.21/Bell 103 mode select 1 Enable V.21/Bell 103 mode select 1 0 Disable unencoded modulation in V.32 mode 1 Enable unencoded modulation in V.32 mode 2 0 Enable V.32 modulation 1 Disable V.32 modulation 3 0 Enable 2100Hz answer tone 1 Disable 2100Hz answer tone 4 0 Disable V.23 fallback mode 1 Enable V.23 fallback mode 5 0 Enable V.32bis mode 1 Disable V.32bis mode 6 0 Reserved 7 0 1 Software compatibility mode disabled Software compatibility mode enabled, all connect messages 9.6Kbps or greater expressed as CONNECT 9600 CONNECTION TIME Type: Register Format AT [cmds] S28=n [cmds] Range: 0-255 Unit: .01 second Description: Sets V.32 duration Command Function S28=0 Eliminates the V.32 answer tone for a faster connection S28=8 Times are in .1 second S28=255 Disable connections except V.32 at 9600bps FALLBACK TIMER Type: Register Format AT [cmds] S29=n [cmds] Range: 0-255 Unit: .01 second Description: Sets the duration of the V.21 answer mode fallback timer TAD AUDIO Type: Register Format AT [cmds] S31=n [cmds] Range: 0-255 Description: Adjusts the TAD audio level BIT-MAPPED REGISTER S32 Format: AT [cmds] S32=n [cmds] Range: 0-255 Description: Select setup for 28.8 and higher speed modems Bit Value Function 0 0 Disable V.8 call indicate 1 Enable V.8 call indicate 1 0 Disable V.8 mode 1 Enable V.8 mode 2 0 Reserved 3 0 Enable V.34 modulation 1 Disable V.34 modulation 4 0 Enable V.34+ modulation 1 Disable V.34+ modulation 5 0 Enable x2 modulation 1 Disable x2 modulation 6-7 0 Reserved BIT-MAPPED REGISTER S33 Format: AT [cmds] S33=n [cmds] Range: 0-255 Description: Disable/enable data rates Bit Value Function 0 0 Enable 2400 symbol rate 1 Disable 2400 symbol rate 1 0 Enable 2743 symbol rate 1 Disable 2743 symbol rate 2 0 Enable 2800 symbol rate Disable 2800 symbol rate 3 0 Enable 3000 symbol rate 1 Disable 3000 symbol rate 4 0 Enable 3200 symbol rate 1 Disable 3200 symbol rate 5 0 Enable 3429 symbol rate 1 Disable 3429 symbol rate 6 0 Reserved 7 0 Enable shaping 1 Disable shaping BIT-MAPPED REGISTER S34 Format: AT [cmds] S34=n [cmds] Range: 0-255 Description: Disable/enable trellis encoding Bit Value Function 0 0 Enable 8S-2D trellis encoding 1 Disable 8S-2D trellis encoding 1 0 Enable 16S-4D trellis encoding 1 Disable 16S-4D trellis encoding 2 0 Enable 32S-2D trellis encoding 1 Disable 32S-2D trellis encoding 3 0 Enable 64S-4D trellis encoding 1 Disable 64S-4D trellis encoding 4 0 Enable non-linear coding 1 Disable non-linear coding 5 0 Enable TX level deviation 1 Disable TX level deviation 6 0 Enable pre-emphasis 1 Disable pre-emphasis 7 0 Enable pre-coding 1 Disable pre-coding CONNECTION - SETUP Type: Register Format AT [cmds] S35=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S35=0 Speed of last connection S35=1 28.8Kbps S35=2 26.4Kbps S35=3 24.0Kbps S35=4 21.6bps S35=5 19.2Kbps S35=6 16.8Kbps S35=7 14.4Kbps S35=8 Modem server operation enabled S35=16 Modem A law operation enabled S35=32 Automatic A/u law detection disabled S35=64 Reduced power disabled S35=128 Reserved BIT-MAPPED REGISTER S42 Format AT [cmds] S42=n [cmds] Range: 0-128 Unit: Bit-mapped Description: GPI definition (Macintosh only). Bit Value Function 0-2 00 Not active 01 CD signal 10 RI signal 11 DSR signal 100 ARQ signal 101 Unidentified 110 Unidentified 111 Unidentified 3-7 0 Reserved